{"id":639,"date":"2026-10-29T13:09:57","date_gmt":"2026-10-29T05:09:57","guid":{"rendered":"http:\/\/www.bestoutrightnow.com\/blog\/?p=639"},"modified":"2026-10-29T13:09:57","modified_gmt":"2026-10-29T05:09:57","slug":"how-to-insulate-a-refrigerator-with-eps-foam-board-416f-585661","status":"publish","type":"post","link":"http:\/\/www.bestoutrightnow.com\/blog\/2026\/10\/29\/how-to-insulate-a-refrigerator-with-eps-foam-board-416f-585661\/","title":{"rendered":"How to insulate a refrigerator with EPS foam board?"},"content":{"rendered":"

Alright, let\u2019s cut to the chase\u2014if you\u2019re looking to level up your fridge\u2019s efficiency, keep those groceries fresh longer, and slash your energy bills, insulating it with EPS foam board is hands down one of the smartest, easiest upgrades you can make. I\u2019m from an EPS foam board supply company, and let me tell you, this isn\u2019t some random hack we push just to move product; it\u2019s actually backed by how EPS works and how fridges were designed to work (well, sort of). A lot of people don\u2019t realize that most fridges only have a thin layer of insulation, especially older models (we\u2019re talking 10+ years old here) that lose up to 30% of their cold air through the walls because that original foam has settled, degraded, or just wasn\u2019t thick enough. EPS Foam Board<\/a><\/p>\n

<\/p>\n

First, let\u2019s get one thing straight: EPS isn\u2019t that \u201cstyrofoam\u201d packing stuff you throw away\u2014wait, no, it is, but the good, high-density EPS we supply is way different. That cheap packing foam is low-density (like 0.5 lbs per cubic foot) and breaks down in months, but our EPS is usually 1.5 to 2.0 lbs per cubic foot, with closed-cell structure that traps tiny air bubbles. That\u2019s the key here: heat transfer is mostly through air, right? So trapping that air means your fridge doesn\u2019t have to work overtime to keep the temp down.<\/p>\n

Now, why should you even bother insulating your fridge? Let\u2019s do a quick real math check. A standard 18 cu ft top-freezer fridge uses about 500 kWh a year if it\u2019s new, but an old one can hit 700 kWh. If you upgrade the insulation with EPS, you can knock 15-20% off that energy use\u2014so that\u2019s $60-$80 a year in savings, depending on your electric rate. Plus, your freezer won\u2019t frost over as fast, your milk won\u2019t go bad in a week because the door warms up the inside, and your fridge compressor won\u2019t cycle on and off every 10 minutes (that\u2019s where most of the wear happens, so this will make your fridge last longer too).<\/p>\n

Enough with the hype\u2014let\u2019s walk through the actual step-by-step process, and we\u2019re gonna be realistic here: this isn\u2019t for a $10k commercial fridge, but for residential fridges (counter-depth, top-freezer, side-by-side) it\u2019s totally doable in a weekend. First, you need the right supplies. Obviously, EPS foam board is non-negotiable. Don\u2019t go with rigid foam from a hardware store that\u2019s not EPS\u2014those are usually polystyrene or polyurethane, and EPS is way easier to cut, cheaper for large projects, and works better for fridge insulation. You\u2019ll also need a utility knife (or a hot wire cutter if you have one\u2014way easier, no ragged edges), a measuring tape, a marker, some spray adhesive (high-temp, since fridges do get a little warm on the outer walls, but not too much\u2014look for one that works on plastic and foam), painter\u2019s tape (to hold the foam while the adhesive dries), and a drill with small screws (optional, but good for securing the bottom panel if your fridge sits on it directly).<\/p>\n

Wait, quick pro tip: don\u2019t insulate the outer metal skin of the fridge\u2019s exterior! That\u2019s a mistake a lot of DIYers make. The outer skin is there to dissipate heat from the condenser coils (which are usually on the back or bottom of the fridge). If you cover that with foam, the condenser can\u2019t release heat, and your fridge will actually run worse. We see this all the time\u2014people call us saying their fridge is colder than normal but running nonstop, and 9 times out of 10 they wrapped the whole thing. Stick to the inner walls, inner door panels, and the back side of the fridge\u2019s inner shell (not the outer back plate).<\/p>\n

Now, let\u2019s break down the steps. First, empty the fridge. I know, no one wants to do this, but you can\u2019t insulate over a half-eaten pint of ice cream. Remove all shelves, drawers, and the inner liners. Wait, if your fridge has a foam-in-place inner liner (most do), you\u2019ll see gaps around the edges, where the liner meets the metal frame, and maybe some spots where the foam has crumbled. That\u2019s exactly where we\u2019re gonna add the EPS.<\/p>\n

Second, measure your panels. For the inner walls (left, right, back, floor), you want to cut EPS boards to fit snugly, not too tight that you have to force it, but not so loose there\u2019s a gap. Gaps are your enemy here\u2014cold air will escape through empty space. So measure each wall at three points (top, middle, bottom) because fridge inner walls are rarely perfectly straight. For example, if the back wall is 24 inches wide at the top and 23.75 inches at the bottom, cut your EPS to the smallest measurement so it fits without bending.<\/p>\n

Third, cut the EPS. If you have a hot wire cutter, that\u2019s perfect\u2014run it slow, don\u2019t force it, and you\u2019ll get a clean, smooth edge. If you only have a utility knife, score the board twice along your line, then snap it like you would drywall. For curved edges (like the back wall of a side-by-side fridge that\u2019s contoured), you can heat the knife a little (hold it over a stove burner for 10 seconds, wait a minute so it doesn\u2019t melt the foam) and cut slowly along the curve. Avoid jagged edges\u2014they might leave gaps, and gaps = heat transfer.<\/p>\n

Fourth, prep the surface. Wipe down the inner walls with a dry cloth to remove any dust, crumbs, or old foam bits. If there are any loose areas on the original inner liner, use a little bit of old adhesive to stick them down first\u2014no need for fancy stuff, just a dab.<\/p>\n

Fifth, glue and stick. Apply a thin, even layer of spray adhesive to the back of the EPS board and to the inner wall. Wait 30-60 seconds (read the adhesive can, but for foam, 45 seconds is sweet spot\u2014if you stick it too fast, it\u2019ll slide; too slow, it won\u2019t grab). Then press the EPS firmly to the wall, starting from the top and working your way down. Use painter\u2019s tape to hold it in place for 15 minutes while the adhesive cures\u2014this is super important, especially on vertical walls, because EPS is light and wants to fall off. For the floor panel, if your fridge\u2019s floor is metal and smooth, you can skip adhesive and just use two small screws in the corners to hold it down, plus a layer of painter\u2019s tape across the top to keep it from sliding under the heavy drawers.<\/p>\n

Sixth, do the inner doors. This is a big one\u2014door insulation is where most of the cold air escapes, because you open it all the time. The inner door panels are usually thin, so cut EPS to fit each door, same as the walls. If your door has a handle, cut a hole in the EPS for it\u2014measure the handle\u2019s base first, leave a little extra space so the door still closes. Glue it to the back of the inner door, tape it until it\u2019s dry, and that\u2019s it. No need to cover the outer door surface, just the inner side that touches the cold air.<\/p>\n

Wait, what about the top freezer? Same rules apply\u2014insulate the inner walls and door, not the outer top. If you have a chest freezer, you can line the inner walls and lid with EPS too, which is even more effective because chest freezers have more open surface area.<\/p>\n

Now, let\u2019s talk mistakes to avoid. First, using too thin EPS. If you get 1-inch EPS, that\u2019s a start, but 1.5 to 2 inches is way better for residential fridges. We see people try \u00bd-inch and it does almost nothing\u2014waste of time and money. Second, leaving gaps. If two EPS boards meet, leave a 1\/8-inch gap and fill it with a little silicone caulk (foam-safe, of course) so cold air doesn\u2019t leak through. Third, insulating the condenser coils. I can\u2019t say this enough\u2014those coils need to release heat, so if you cover the outer back or bottom plate, your compressor will overheat and die faster. Fourth, not letting the adhesive cure. I\u2019ve seen people yank the painter\u2019s tape off after 5 minutes and the EPS slides right off\u2014patience here pays off.<\/p>\n

Another thing: what if your fridge has a metal outer back plate? Can you insulate the back of the outer plate? No, wait\u2014only if you\u2019re insulating the space behind the fridge, not the plate itself. If your fridge is in a cabinet, you can cut a thick EPS board to fit the cabinet space behind the fridge, which adds extra insulation between the fridge and the wall. That\u2019s a bonus tip for people with built-in fridges\u2014way more effective than adding it to the inner walls sometimes.<\/p>\n

Now, let\u2019s get into the science a little, because you don\u2019t have to take my word for it. EPS foam has a R-value of about 4.5 per inch, meaning 2-inch EPS gives you R-9, which is about as good as the insulation in some older home walls. Compare that to the typical \u00bd-inch insulation in a fridge, which is R-2.25\u2014so adding 1.5 inches of EPS more than doubles the insulation power. That\u2019s why the energy savings are so real. The closed-cell structure of EPS means it doesn\u2019t absorb moisture either, which is huge because if insulation gets wet, its R-value drops like a rock. Other foams, like polystyrene, absorb moisture, so EPS is the way to go for fridges that might have a little condensation over time.<\/p>\n

Wait, what about if you have a new fridge? You still might want to add EPS. Even new fridges sometimes have thin insulation, especially budget models. A lot of manufacturers use the minimum amount of foam to cut costs, so adding a layer of EPS can give it that extra boost it needs to run at peak efficiency. We supply a lot of EPS to people with brand-new fridges who noticed their energy bill didn\u2019t drop as much as the salesperson promised\u2014this fixes that.<\/p>\n

Now, let\u2019s talk about how to source the right EPS. Don\u2019t go for random Amazon packs of craft EPS\u2014those are low-density, not for structural or insulation use. Look for high-density EPS boards (1.5 to 2.0 lbs per cubic foot) from a supplier that specializes in insulation-grade EPS, like us. We cut custom sizes too, so if your fridge has weird, non-standard inner walls, just shoot us the measurements and we can cut the EPS to fit exactly\u2014no wasted material, no extra work for you.<\/p>\n

Once you\u2019ve got the EPS cut, the rest is easy. Just follow the steps I laid out, and you\u2019ll have your fridge insulated in a weekend. The payoff? Lower energy bills, a longer-lasting fridge, and less food waste because your temps stay consistent.<\/p>\n

<\/p>\n

Wait, one last tip: after you\u2019re done, let the fridge run empty for 24 hours before restocking. That gives the adhesive time to fully cure, and the foam time to adjust to the cold temperature. If you put heavy drawers or shelves right back on, you might accidentally push the EPS loose before it\u2019s stuck properly.<\/p>\n

XPS Underfloor Heating Panels<\/a> Now, if you\u2019re thinking, \u201cI don\u2019t want to deal with cutting and measuring, just get the right EPS for my fridge,\u201d or you want to ask about custom cuts, high-density EPS, or even bulk orders for multiple fridges (like if you run a small cafe with old fridges), we\u2019re here to help. We supply insulation-grade EPS foam boards perfect for fridge insulation, and our team can answer any questions you have about thickness, cutting, or installation. Hit us up to talk pricing, get a sample, or work out the right amount for your project\u2014no hoops, no fine print, just straight-up advice from people who know EPS and fridges.<\/p>\n

References<\/h2>\n
    \n
  1. U.S. Department of Energy. (2022). "Residential Refrigerator Energy Efficiency: Savings Opportunities."<\/li>\n
  2. American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE). (2021). "Thermal Properties of Building Materials: Closed-Cell Polymeric Foams."<\/li>\n
  3. International Association of Home Inspectors (IAHI). (2020). "Common Fridge Insulation Deficiencies and Remedies."<\/li>\n
  4. EPS Industry Alliance. (2023). "EPS Foam Applications for Appliance Insulation."<\/li>\n<\/ol>\n
    \n

    Shanxi Rongshengchang Trading Co., Ltd.<\/a>
    As one of the most professional eps foam board suppliers in China, we’re featured by quality products and good price. Please rest assured to buy premium eps foam board for sale here from our factory. Welcome to view our website for more information.
    Address: No.1602, 16th Floor, Unit 4, Building 13, Pingyang Jingyuan, No.65 Pingyang Road, Pingyang Road Street, Xiaodian District, Shanxi Province, China
    E-mail: postmaster@rongshengchang.com
    WebSite:     https:\/\/www.rongshengchang.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    Alright, let\u2019s cut to the chase\u2014if you\u2019re looking to level up your fridge\u2019s efficiency, keep those … How to insulate a refrigerator with EPS foam board?<\/span>Read more<\/a><\/p>\n","protected":false},"author":155,"featured_media":639,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[602],"class_list":["post-639","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-eps-foam-board-47c8-588c60"],"_links":{"self":[{"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/posts\/639","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/users\/155"}],"replies":[{"embeddable":true,"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/comments?post=639"}],"version-history":[{"count":0,"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/posts\/639\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/posts\/639"}],"wp:attachment":[{"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/media?parent=639"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/categories?post=639"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.bestoutrightnow.com\/blog\/wp-json\/wp\/v2\/tags?post=639"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}